DIN Abrasion Tester

DIN Abrasion Tester

(4 đánh giá)

AB-6111

Ueshima

12 months

Ueshima AB-6111 DIN Abrasion Tester

 

This equipment has a drum with abrasive cloth around it and rotating at a certain speed. A test piece is pushed on the abrasive cloth and being worn for evaluating abrasion resistance of vulcanized rubber.
Applicable standards: JIS K6264-2, DIN53516, ISO4649, GB/T9867
Specifications
Test Piece                :φ16±0.2mm, 6- to 15-mm thick
Test Method             :Method A (with a test piece not rotating)
Method B (with a test piece rotating during a test)
Load                         :10±0.2N, 5.0±0.1N
Traverse                   :4.2±0.04mm (per rotation of the drum)
Drum Diameter          :φ150±0.2mm Drum Width             :460mm Drum Speed             :40±1rpm
Abrasion Distance  :40m (84 rotations of the drum), or
20m (42 rotations of the drum)
Abrasion Speed      :0.32m/sec
Sample Slant Angle :3°
Outer Dimensions   :approx. 615(W)×310(D)×440(H)mm
Weight                      :approx. 55kg
Power Supply          :AC200V   10A   50Hz
Accessories             :・2.5-N weight                              1 piece
・5-N weight                                 1 piece
・Calibration tool (metal piece)    2 pieces
・Hexagon wrench                       2 pieces (M4 and M3)
・No rotation plate                        1 piece
・2-mm thickness gauge              1 piece
・20-m test block                          1 piece
・Rotation blade for a sample      1 piece
・Reference rubber sheet            1 sheet (D1, 181×181×8mm)
・Double sided adhesive tape      1 roll
・Abrasion cloth (#60)                  5 sheets
Option                      :・Vacuum cleaner
・MD-4504 sample preparation mold (φ16×15, 4 cavities

 

Đánh giá sản phẩm

Bình chọn sản phẩm:

Bình luận

Sản phẩm cùng loại

Mooney Viscometer

Mooney Viscometer

VR-1130 Series Mooney Viscometer: ●Measurement of Mooney viscosity for unvulcanized rubber ●Measurement of scorch time for unvulcanized rubber ●Measurement of Mooney stress relaxation for unvulcanized rubber (MODEL: VR-1132), ムーニー粘度計
Flat Die Rheometer (FDR)

Flat Die Rheometer (FDR)

Flat Die Rheometer (FDR) VR 3110 JIS K6300-2, ISO 6502, ASTM D 5289 (Oscillating Sealed Flat Die Cavity Rotorless Curemeter) FDR (Flat Die Rheometer), manufactured by Ueshima Seisakusho Co., Ltd., 加硫試験機
Blow-Point Analyzer

Blow-Point Analyzer

Ueshima Blow-Point Analyzer
GEHMAN’S TORSION TESTER

GEHMAN’S TORSION TESTER

Standard: JIS K 6261, ISO 1432, ASTM D1053 , Rubber loses resiliency as temperature goes down. The frozen rubber can't keep its essential characteristics under the temperature below Glass Transition Point. In fact, the rubber applications under severe environments such as vehicle tire in frozen area and aircraft components in the stratosphere are seriously affected. It is a vital importance with the rubber applicants to test low temperature characteristics of vulcanized rubber.
Cable Abrasion Tester

Cable Abrasion Tester

The Cable Abrasion Tester is for cable insulation and is of the type that fixes a test piece in contact with abrasion tape,loads it,and moves the abrasion tape at a speed of 1,500 mm/min. The tester also measures the length of abrasion tape used until the cable insulation abrasions out and the conductor wire gets into contact with the wear tape. Applicable Standard:JIS C3406 Length of Test Piece:Approx 900mm

Low Temperature Brittleness Tester

Low Temperature Brittleness Tester

Low Temperature Brittleness Tester The brittleness tester conforms to JIS K 6261 / JIS K 7216 and determines the brittleness temperature and the 50% brittleness temperature of vulcanized rubber and plastics in a low-temperature environment. TM-2131 is the single type which comes with a set of sample holder, holding five samples, and TM2136 is the multiple type with four sets of sample holders with which four sets of five samples can be tested continuously just by turning a dial to change sample
Dynamic Mechanical Analyzer

Dynamic Mechanical Analyzer

Ueshima Dynamic Mechanical Analyzer

GAS PERMEABILITY TESTER

GAS PERMEABILITY TESTER

GAS PERMEABILITY TESTER This tester conforms to ASTM D1434 and JIS K7126, allowing to measure gas permeability of such specimen like rubber and plastic film using differential pressure method. A cell divided by the specimen is subject to different pressure on each side of the cell. Gas permeability rate is measured from the pressure gradient changing as time passes. Measurements can be done under different temperature environment using a temperature controlled bath.
RTM Friction Tester (Tire)

RTM Friction Tester (Tire)

FR-7225 RTM Friction Tester enables to evaluate friction characteristics of tire tread compound on material testing basis, and can be tested in Dry, Wet, Ice conditions on ring shaped road surface. Test is performed by pressing specimen on constantly rotating ring shaped wheel at free rolling condition, or with slip ratio applied in 0 to +/- 95% range and measuring the friction force. Also, max. 30deg. slip angle can be applied on the specimen against it’s tangential line.
GEER’S AGING OVEN

GEER’S AGING OVEN

Ueshima GEER’S AGING OVEN Most important functions like temperature uniformity, wind velocity and air ventilation rate are in accordance with JIS K 6257 and/or JIS K 7212. ○The minimized shape of the series allows use on a table. We also provide with an exclusive stand. ○It is able to place two units in tiers, minimizing the footprint.
Tensile testing machine

Tensile testing machine

Ueshima TS-2632 Tensile testing machine

Top

  Zalo