Plastic testing equipment

Wazau UL 1581 Electrical Cables and Wires Flame Test Chamber is used to determine the flame propagation through electrical cables and wires.

Contact Us: Email: secovina@vnn.vn OR  Mr. Thomas Reinheimer, Email: reinheimer@wazau.com, Phone: +49 (0)30 3443088

Wazau UL94 Flammability Test Chamber is used to test the flammability of plastic materials for parts in devices and appliances.

Contact Us: Email: secovina@vnn.vn OR  Mr. Thomas Reinheimer, Email: reinheimer@wazau.com, Phone: +49 (0)30 3443088

The EQUILAM NA C.C.T Cyclic Corrosion Test chambers provide the best simulation for accelerated corrosion testing. Some studies indicate that the tests results closely resemble those obtained in outdoor exposure. Samples can be exposed to different environmental conditions. Contact Us: Email: secovina@vnn.vn  OR  Mr. Felipe Rojo, Email: frojo@equilamna.com , Phone: 1.754.900.7816

Ueshima Dynamic Mechanical Analyzer (DMA)

Dupont’s Impact Tester is used to measure the resistance of specimen (painted plate, hard plastic sheet, etc.) against impact force by observing the appearance of crack and peeling.
 

50 TONS LABORATORY PRESS MACHINE with ELECTRIC HEATING WATER COOLING TYPE. The material is placed in the casting mould and clamped between the electric-heating flat plates to apply pressure and temperature for making the material shape, testing and serving as the basis for the ingredient of mass production. It has the function of automatic and manual operation switching.

The Cable Abrasion Tester is for cable insulation and is of the type that fixes a test piece in contact with abrasion tape,loads it,and moves the abrasion tape at a speed of 1,500 mm/min. The tester also measures the length of abrasion tape used until the cable insulation abrasions out and the conductor wire gets into contact with the wear tape. Applicable Standard:JIS C3406 Length of Test Piece:Approx 900mm

Ueshima Model : AB-5100 Series Cable Abrasion Tester

- 2 HORIZONTAL ROLL EACH 4×12(IN) DIAMETER×FACE WIDTH) - HARDNESS 60 HRC (= 800 HV) OR ABOVE - CHROMING DEPTH 0.1 mm - 0.5 μm ROUGHNESS - POLISHING RA 0.05 - 2 SET OF TEMPERATURE CONTROLLER - 1 SET OF 6 POLE 2HP MOTOR AND REDUCER - FRONT ROLL ABOUT 20 R.P.M.、REAR ROLL ABOUT 24 R.P.M. (RATIO 1:1.2) - ROLLER GAP (SHEETING-OUT THICKNESS) 0.12 – 7mm - ELECTRIC HEATING SYSTEM MAX 210℃ - EACH 1.5KW TOTAL 3KW - 2 SOLID HANDWHEELS FOR THE ADJUSTMENT OF SHEETING-OUT THICKNESS -

The Durometer comes in two models (type A for midium materials to be measured and type D for hard materials). Type D is suitable for the cases where type A measurement values reach 90 or more.

The United Model DSTM testing machine is a computer inclusive, electromechanical, test system designed to accommodate a variety of testing instruments and accessories to test various types of material including ceramics, plastics, polymers, metals and composites. Contact a United sales representative for more details. The United Model DSTM testing machine are available in four standard load frame capacities: 2.5kN, 5kN, 10kN and 20kN.

Foam testing machine to ASTM D3574

CT Compression Molding Machine or CT hydraulic press, is for polymeric shaping in which the molding material, generally preheated, is first placed in an open, heated mold cavity.

United DSTM-10KN Universal Testing Machine

Solids Density Meter 

Application:rubber,plastic,cables,hard alloy,glass,new materials researching laboratory.
Standards:According to ASTM D792,GB/T1033,GB/T2951,JIS K6268,ISO 2781,ISO 1183,GB/T208,GB/T5163,GB/T 1933 standards etc.
DH300 is one of the densimeter that have been widely applying to industry,using water as medium,the density value can be displayed after two steps.Compared with traditional densimeter,there is no calculation by hand,which is more convenient.
 

Ueshima GEER’S AGING OVEN Most important functions like temperature uniformity, wind velocity and air ventilation rate are in accordance with JIS K 6257 and/or JIS K 7212. ○The minimized shape of the series allows use on a table. We also provide with an exclusive stand. ○It is able to place two units in tiers, minimizing the footprint.

The Pneumatic Drive Press Cutting Machine is mainly applied for punching rubber sheets, soft plastics, film and other materials. Pneumatic pressure alone is used to ensure a compact size.

UESHIMA FT-1521 DEMATTIA FLEX CRACKING TESTER