AB-1150 LAMBOURN ABRASION TESTER

AB-1150 LAMBOURN ABRASION TESTER

(6 đánh giá)

AB-1150

Ueshima Japan

12 months

Among various abrasion tester for rubber such as tire, belt, and sole etc., it is Lambourn Type Abrasion Tester that is evaluated as the best reappearance in JIS K6264(Abrasion Testing Method of Vulcanized Rubber) as well as high correlation with the result of product test.

AB-1150 LAMBOURN ABRASION TESTER

Manufacturer: Ueshima – Nhật

Outline:

Among various abrasion tester for rubber such as tire, belt, and sole etc., it is Lambourn Type Abrasion Tester that is evaluated as the best reappearance in JIS K6264(Abrasion Testing Method of Vulcanized Rubber) as well as high correlation with the result of product test.

MODEL AB-1150 with high accuracy and stability invented in the method of load which has the largest influence on abrasion test result. As the result, high-performance & low-cost material tester which is available for direct simulation of quality test, was introduced to the field of tribology.

 

Feature

○The most suitable test condition to simulate the particular product such as tire, belt, roller, and sole etc., , can be selected.

○Instead of dead weight method for pressing force to the testpiece , feed back control method(Patent Pending) which is loaded by air cylinder and is detected by load-cell, is adopted. As a result , not only highly accurate and stable test condition can be obtained, but also bounding problem is solved by highly corresponding damping.

○Both rotating axis of testpiece and glindstone are feed back controlled independently by servo motor to test under conditions of more stable circumferential speed and slip ratio.

 

Specification:

Applicable Standard: JIS K6264-2, ISO23337

Dimensions of testpiece:  Diameter 49mm, Inner dia. 23mm, Thickness 5mm or 10mm

Dimensions of grindstone:  Diameter 175mm, thickness 25mm

Material of grindstone: Grain: C, grain size:80, binding strength: K, (JIS R6210)

Circumferential speed of testpiece: 10 to 200m/min., driven & controlled by AC servo motor

Circumferential speed of grindstone: 10 to 200m/min., driven & controlled by AC servo motor Grindstone speed is automatically determined by setting the sample speed and slip ratio.

Indication of circumferential speed: Digital 4 digits indication (testpiece & grindstone)

Slip ratio setting: Arbitrary setting in 5 to 80% range. (Setting unit 0.1%)

Loading load: Load can be arbitrary set in 5 to 80N range. Air cylinder drive, load cell detection feedback control.

Torque: Sample axis 5Nm

Output: Load, torque DC 0 to 5V

Setting time: Max.999min.59sec.

Temperature inside test chamber(option): Room temperature +10℃ to 120℃

Sand dropping device: Container capacity 4 liter, helical gear drive sand drop type, sand collection in box placed at bottom of the chamber. Kind of sand: carborundum grit 80(JIS R 6111)

Electric and air sources: 3 Phases, AC200V, 50/60Hz

Air: Dry clean air 0.5 to 0.8Mpa

Outside dimensions: 810W x 830D x 1150H1980 With optional stand(H)mm

Weight: 380kg (Body and Stand)

OPTION: Temperature measuring device for testpiece, stand, mold for testpiece preparation

Đánh giá sản phẩm

Bình chọn sản phẩm:

Bình luận

Sản phẩm cùng loại

Constant-stress/strain flexometer

Constant-stress/strain flexometer

Rubber, vulcanized — Determination of temperature rise and resistance to fatigue in flexometer testing: Constant-stress/strain flexometer. This machine determines change in complex modulus of elasticity E', E", tan6 and heating rate of rubber during the thermal fatigue process. Standard: ISO 4666, JIS K 6265,...

Mooney Viscometer

Mooney Viscometer

VR-1130 Series Mooney Viscometer: ●Measurement of Mooney viscosity for unvulcanized rubber ●Measurement of scorch time for unvulcanized rubber ●Measurement of Mooney stress relaxation for unvulcanized rubber (MODEL: VR-1132), ムーニー粘度計

Flat Die Rheometer (FDR)

Flat Die Rheometer (FDR)

Flat Die Rheometer (FDR) VR 3110 JIS K6300-2, ISO 6502, ASTM D 5289 (Oscillating Sealed Flat Die Cavity Rotorless Curemeter) FDR (Flat Die Rheometer), manufactured by Ueshima Seisakusho Co., Ltd., 加硫試験機

Dynamic Mechanical Analyzer (DMA)

Dynamic Mechanical Analyzer (DMA)

Ueshima Dynamic Mechanical Analyzer (DMA)

Maron Type Mechanical Stability Tester

Maron Type Mechanical Stability Tester

Ueshima MS-5150 Maron Type Mechanical Stability Tester : The Maron-type mechanical stability tester is a testing machine that measures the coagulation content in latex generated by rotating a rotating disc at a constant speed while pressing it against the sample container with a fixed pressure.

VR-6155

VR-6155

JIS K6249, ASTM D926 and ISO 7323

FPS WEAR TESTING SYSTEM

FPS WEAR TESTING SYSTEM

A Lambourn abrasion tester or conventional FPS tester, which is used for abrasion tests of high polymer material for such products like tire and belt, controls slip ratio or speed difference between test piece and road wheel while doing an abrasion test.

* FPS stands for Field Performance Simulation.

TR Tester

TR Tester

This device measures the retraction rate of elongation when a specimen is subjected to a certain elongation, frozen, and then gradually warmed up. The encoder is used to measure the retraction, and a PC is used to set test conditions, display data (TR value, retraction rate), draw graphs (temperature, retraction rate), and save the results to a file. Standard JIS K 6261-4,ISO2921,ASTM D 1329.

Akron Abrasion Tester

Akron Abrasion Tester

ISO 23794:2023: Rubber, vulcanized or thermoplastic — Abrasion testing: Ueshima AB-1511 Akron Abrasion Tester

Dupont Impact Tester

Dupont Impact Tester

Dupont’s Impact Tester is used to measure the resistance of specimen (painted plate, hard plastic sheet, etc.) against impact force by observing the appearance of crack and peeling.
 

GEHMAN’S TORSION TESTER

GEHMAN’S TORSION TESTER

Standard: JIS K 6261, ISO 1432, ASTM D1053 , Rubber loses resiliency as temperature goes down. The frozen rubber can't keep its essential characteristics under the temperature below Glass Transition Point. In fact, the rubber applications under severe environments such as vehicle tire in frozen area and aircraft components in the stratosphere are seriously affected. It is a vital importance with the rubber applicants to test low temperature characteristics of vulcanized rubber.

Cable Abrasion Tester

Cable Abrasion Tester

The Cable Abrasion Tester is for cable insulation and is of the type that fixes a test piece in contact with abrasion tape,loads it,and moves the abrasion tape at a speed of 1,500 mm/min. The tester also measures the length of abrasion tape used until the cable insulation abrasions out and the conductor wire gets into contact with the wear tape. Applicable Standard:JIS C3406 Length of Test Piece:Approx 900mm

Top

  Zalo