Low Temperature Brittleness Tester

Low Temperature Brittleness Tester

(6 đánh giá)

TM-2200 Series

Uehima

12 months

Low Temperature Brittleness Tester The brittleness tester conforms to JIS K 6261 / JIS K 7216 and determines the brittleness temperature and the 50% brittleness temperature of vulcanized rubber and plastics in a low-temperature environment. TM-2131 is the single type which comes with a set of sample holder, holding five samples, and TM2136 is the multiple type with four sets of sample holders with which four sets of five samples can be tested continuously just by turning a dial to change sample

SPECIFICATIONS

Model TM-2210 TM-2215 TM-2220 TM-2225
Cooling Method Refrigerator Dry Ice Refrigerator Dry Ice
Chuck Single Type Multiple Type
Standard JIS K 6261-2、JIS K 7216, ISO 812
Hammer Speed 1.4~2.4m/sec variable
Hammer Tip 1.6±0.1mm
Temp. Range -70℃ - 20℃
Heat Transfer Medium Ethanol or IPA
Temp. Control PID temperature controller with P-T100Ω
Safety Device Leakage breaker,overheat protector
Power Supply 200V AC or specified voltage, 3 phases, 30A 50/60Hz(refrigerator type)
200V AC or specified voltage, 3 phases, 15A 50/60Hz(dry ice type)
Options Sample cutting blade, JIS K 7216 type B chuck

Đánh giá sản phẩm

Bình chọn sản phẩm:

Bình luận

Sản phẩm cùng loại

Constant-stress/strain flexometer

Constant-stress/strain flexometer

Rubber, vulcanized — Determination of temperature rise and resistance to fatigue in flexometer testing: Constant-stress/strain flexometer. This machine determines change in complex modulus of elasticity E', E", tan6 and heating rate of rubber during the thermal fatigue process. Standard: ISO 4666, JIS K 6265,...

Mooney Viscometer

Mooney Viscometer

VR-1130 Series Mooney Viscometer: ●Measurement of Mooney viscosity for unvulcanized rubber ●Measurement of scorch time for unvulcanized rubber ●Measurement of Mooney stress relaxation for unvulcanized rubber (MODEL: VR-1132), ムーニー粘度計

Flat Die Rheometer (FDR)

Flat Die Rheometer (FDR)

Flat Die Rheometer (FDR) VR 3110 JIS K6300-2, ISO 6502, ASTM D 5289 (Oscillating Sealed Flat Die Cavity Rotorless Curemeter) FDR (Flat Die Rheometer), manufactured by Ueshima Seisakusho Co., Ltd., 加硫試験機

Dynamic Mechanical Analyzer (DMA)

Dynamic Mechanical Analyzer (DMA)

Ueshima Dynamic Mechanical Analyzer (DMA)

Maron Type Mechanical Stability Tester

Maron Type Mechanical Stability Tester

Ueshima MS-5150 Maron Type Mechanical Stability Tester : The Maron-type mechanical stability tester is a testing machine that measures the coagulation content in latex generated by rotating a rotating disc at a constant speed while pressing it against the sample container with a fixed pressure.

VR-6155

VR-6155

JIS K6249, ASTM D926 and ISO 7323

AB-1150 LAMBOURN ABRASION TESTER

AB-1150 LAMBOURN ABRASION TESTER

Among various abrasion tester for rubber such as tire, belt, and sole etc., it is Lambourn Type Abrasion Tester that is evaluated as the best reappearance in JIS K6264(Abrasion Testing Method of Vulcanized Rubber) as well as high correlation with the result of product test.

FPS WEAR TESTING SYSTEM

FPS WEAR TESTING SYSTEM

A Lambourn abrasion tester or conventional FPS tester, which is used for abrasion tests of high polymer material for such products like tire and belt, controls slip ratio or speed difference between test piece and road wheel while doing an abrasion test.

* FPS stands for Field Performance Simulation.

TR Tester

TR Tester

This device measures the retraction rate of elongation when a specimen is subjected to a certain elongation, frozen, and then gradually warmed up. The encoder is used to measure the retraction, and a PC is used to set test conditions, display data (TR value, retraction rate), draw graphs (temperature, retraction rate), and save the results to a file. Standard JIS K 6261-4,ISO2921,ASTM D 1329.

Akron Abrasion Tester

Akron Abrasion Tester

ISO 23794:2023: Rubber, vulcanized or thermoplastic — Abrasion testing: Ueshima AB-1511 Akron Abrasion Tester

Dupont Impact Tester

Dupont Impact Tester

Dupont’s Impact Tester is used to measure the resistance of specimen (painted plate, hard plastic sheet, etc.) against impact force by observing the appearance of crack and peeling.
 

GEHMAN’S TORSION TESTER

GEHMAN’S TORSION TESTER

Standard: JIS K 6261, ISO 1432, ASTM D1053 , Rubber loses resiliency as temperature goes down. The frozen rubber can't keep its essential characteristics under the temperature below Glass Transition Point. In fact, the rubber applications under severe environments such as vehicle tire in frozen area and aircraft components in the stratosphere are seriously affected. It is a vital importance with the rubber applicants to test low temperature characteristics of vulcanized rubber.

Top

  Zalo